Technical datasheet
Print datasheet:
[Print advise: Scaling on portrait format => 54%, on landscape format => 84%]
Technical datasheet
|
SUMITUBE NH(GS)
Single Wall Polyolefin, 2:1
Operating temperature: -40 up to 105°C Surface: Matt
Marking: | |
|
|
Dimensions
| TRADE SIZE | BEFORE SHRINKAGE | AFTER SHRINKAGE | DELIVERY UNITS * | ||
| [inch] |
Inner diameter (EID) min. [mm] |
Inner diameter (RID) max. [mm] |
Wall thickness (RWT) min.-max. [mm] |
Unit quantity [m] |
Box quantity [m] |
| 1/16 1,60 | 1,60 | 0,80 | Min. 0,60 | 300 | 900 |
| 3/32 | 2,40 | 1,20 | Min. 0,60 | 150 | 900 |
| 1/8 | 3,20 | 1,60 | Min. 0,60 | 150 | 600 |
| 3/16 | 4,80 | 2,40 | 0,70-1,00 | 60 | 300 |
| 1/4 | 6,4 | 3,20 | 0,75-1,05 | 60 | 300 |
| 3/8 | 9,5 | 4,75 | 0,85-1,15 | 30 | 150 |
| 1/2 | 12,7 | 6,4 | 1,02-1,38 | 30 | 150 |
| 3/4 | 19,1 | 9,5 | 1,15-1,65 | 30 | 90 |
| 1 | 25,4 | 12,7 | 1,50-2,10 | 30 | 90 |
| 1-1/2** | 38,1 | 19,1 | 1,50-2,10 | 30 | 90 |
| 2** | 50,8 | 25,4 | Min. 2,00 | 30 | 60 |
| * Non standard colours, larger sizes and cut lenght of 1200mm are available on request. Dimensions according to IEC60684-3-216 class C except for **. | |||||
Colours & Technical drawing
| STANDARD COLOURS | SPECIAL COLOURS | TECHNICAL DRAWING | |||||||||
|
|
 |
Technical properties
| PHYSICAL PROPERTIES | |||
| PROPERTY | TEST METHOD | REQUIREMENT | TYPICAL VALUE * |
| Longitudinal change | IEC 60684-2 | 5 to -10% | Pass |
| Tensile strength | IEC 60684-2 | Min. 7.0 MPa | 19.8 MPa |
| Elongation at break | IEC 60684-2 | Min. 200% | 300% |
| Secant modulus | - | - | 187 MPa |
| THERMAL PROPERTIES | |||
| PROPERTY | TEST METHOD | REQUIREMENT | TYPICAL VALUE * |
| Operating temperature | Life-Curve | -40 up to 105°C | -40 up to 105°C |
| Heat ageing (135°C x 168h) | IEC60684-2 | Tensile strength min. 5.0 MPa | 21.9 MPa |
| Elongation min. 150% | 247% | ||
| Bending at low temperature (-30°C x 4h) | IEC60684-2 | No cracking | Pass |
| Copper corrosion (150°C x 16h) | IEC60684-2 | Max. 8% | No corrosion |
| CHEMICAL PROPERTIES | |||
| PROPERTY | TEST METHOD | REQUIREMENT | TYPICAL VALUE * |
| Flammability | Japanese Railway | Flame retardant | Pass |
| Limiting oxygen index (LOI) | BS6853 | Min. 34% | 41.5% |
| Smoke density | BS6853 | Max. 0.017 m²/g | 0.0072 |
| Toxic fume emission | BS6853 | Max. 1.0 | 0.15 |
| Flame spread index | NFPA130 (ASTM E162) | Max. 35 | 28.1 |
| Smoke density | NFPA130 (ASTM E662) | Ds(1.5min): max. 100 Ds(4min): max. 200 |
With Pilot Flame Ds(1.5min): 1.36 Ds(4min): 11.6 Without Pilot Flame Ds(1.5min): 7.94, Ds(4min): 116 |
| Toxic gas generation | BSS7239 | CO: max. 2500ppm HF: max. 150ppm HCl: max. 300ppm NO2: max. 100ppm SO2: max. 100ppm HCN: max. 100ppm |
With pilot flame CO: 222ppm HF: n.d. HCl: n.d. NO2: <2ppm SO2: n.d. HCN: <0.6ppm Without pilot flame CO: 222ppm HF: n.d. HCl: n.d. NO2: n.d. SO2: n.d. HCN: <0.6ppm |
| Oxygen Index | EN45545-2 | Min. 32% (R22/HL3) | 41.5% |
| Smoke density | EN45545-2 | Max. 150 (R22/HL3) | 11.1 |
| Toxic fume emission | EN45545-2 | Max. 0.75 (R22/HL3) | 0.03 |
| Water absorption (24h, 23°C) | IEC60684-2 | Max. 1.0% | 0.11% |
| Fluid resistance against diesel (168h, 70°C) | IEC60684-2 | Tensile strength min. 4.0MPa | 9.9MPa |
| Elongation min. 100% | 290% | ||
| ELECTRICAL PROPERTIES | |||
| PROPERTY | TEST METHOD | REQUIREMENT | TYPICAL VALUE * |
| Dielectric strength | IEC60684-2 | Min. 15kV/mm | 33.9 kV/mm |
| Volume resistivity (23°C) | IEC60684-2 | Min. 1010Ω·cm | 5.6×1014Ω·cm |
| * For reference purposes only |
Test methods IEC60684-2, requirements IEC60684-3-216, class C.